Stainless steel cutting type
E-BON
E-BON
2018-01-30 17:30:52
10.1 principle of plasma cutting machine:
Taking compressed air as working gas, high temperature and high speed plasma arc as heat source, the cutting metal is partially melted, and the molten metal is blown away at the same time to form narrow slit. The device can be used for cutting all kinds of metal materials such as stainless steel, aluminum, copper, cast iron and carbon steel. It not only cuts fast, has narrow slit, smooth incision, small heat affected zone, low workpiece deformation and simple operation, but also has significant energy saving effect. E-BON the stainless steel specialist, manual coffee grinder manufacturer china.
The device is applicable to all kinds of machinery, metal structure, manufacture, installation and maintenance, of sheet cutting, opening, patching, groove cutting. E-BON the stainless steel specialist, best price Mixing Bowl manufacturer.
Operation rules for plasma cutting machine:
1.1 in order to reduce energy consumption and improve the life of nozzle and electrode, "low gear" should be used as far as possible when cutting the thin workpiece.
1.2 "when cutting thick selection switch is in the" high-grade "should be used for non-contact cutting type cutting (except for exceptional circumstances) and preference of water cutting torch.
1.3 when the switch position of "cutting thick selection" switch must be changed, it is necessary to turn off the mainframe power switch in order to prevent the damage of the machine.
1.4 when dismantling or moving the host, it is necessary to turn off the power supply to prevent the danger.
1.5 should first turn off the power switch, can install accessories, parts of the host (such as cutting and cutting wire, electrode, nozzle, distributor, pressure cap, protective sleeve etc.). Avoid quickly and repeatedly open the torch switch, so as to avoid damage to the arc system or related components.
1.6 when you need to start from the middle of the workpiece arc cutting, cutting stainless steel less than 20mm thick, can directly punch cutting. Methods: the torch in the slit starting point, and the cutting torch nozzle axis and the workpiece plane is approximately 75 DEG angle, then open the switch of cutting torch, the arc perforation; at the same time, slowly adjust the nozzle axis and the workpiece surface angle, cutting the workpiece to wear time should be adjusted to 90 degrees. After cutting the workpiece, it can be cut normally along the direction of the cutting seam. But if the cutting is perforated when the above thickness is above the thickness, a small hole (not limited in diameter) must be drilled at the starting point of the cutting and arc cut from the small hole. Otherwise, easy to damage the cutting torch nozzle.
If you want to get more information about E-BON, you can click manual coffee grinder wholesales.
Taking compressed air as working gas, high temperature and high speed plasma arc as heat source, the cutting metal is partially melted, and the molten metal is blown away at the same time to form narrow slit. The device can be used for cutting all kinds of metal materials such as stainless steel, aluminum, copper, cast iron and carbon steel. It not only cuts fast, has narrow slit, smooth incision, small heat affected zone, low workpiece deformation and simple operation, but also has significant energy saving effect. E-BON the stainless steel specialist, manual coffee grinder manufacturer china.
The device is applicable to all kinds of machinery, metal structure, manufacture, installation and maintenance, of sheet cutting, opening, patching, groove cutting. E-BON the stainless steel specialist, best price Mixing Bowl manufacturer.
1.1 in order to reduce energy consumption and improve the life of nozzle and electrode, "low gear" should be used as far as possible when cutting the thin workpiece.
1.2 "when cutting thick selection switch is in the" high-grade "should be used for non-contact cutting type cutting (except for exceptional circumstances) and preference of water cutting torch.
1.3 when the switch position of "cutting thick selection" switch must be changed, it is necessary to turn off the mainframe power switch in order to prevent the damage of the machine.
1.4 when dismantling or moving the host, it is necessary to turn off the power supply to prevent the danger.
1.5 should first turn off the power switch, can install accessories, parts of the host (such as cutting and cutting wire, electrode, nozzle, distributor, pressure cap, protective sleeve etc.). Avoid quickly and repeatedly open the torch switch, so as to avoid damage to the arc system or related components.
1.6 when you need to start from the middle of the workpiece arc cutting, cutting stainless steel less than 20mm thick, can directly punch cutting. Methods: the torch in the slit starting point, and the cutting torch nozzle axis and the workpiece plane is approximately 75 DEG angle, then open the switch of cutting torch, the arc perforation; at the same time, slowly adjust the nozzle axis and the workpiece surface angle, cutting the workpiece to wear time should be adjusted to 90 degrees. After cutting the workpiece, it can be cut normally along the direction of the cutting seam. But if the cutting is perforated when the above thickness is above the thickness, a small hole (not limited in diameter) must be drilled at the starting point of the cutting and arc cut from the small hole. Otherwise, easy to damage the cutting torch nozzle.
If you want to get more information about E-BON, you can click manual coffee grinder wholesales.